View PM600_402987.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PM600 SERIES
Single and dual output
* * * * * * 24 pin DIP package 1.25 x 0.8 x 0.4 inch package Tight regulation Pi input filter 20mV pk-pk ripple and noise Short circuit protection
[ 2 YEAR WARRANTY ]
The PM600 Series are a broad line of low cost, high performance single and dual output DC/DC converters packaged in an IC compatible 24 pin DIP configuration. These miniature converters are ideal for use on high density PC boards, or wherever low power, isolated and regulated outputs are required. A self contained input Pi network filter, available on all models, minimizes reflected ripple current for critical applications. This feature eliminates the need for external filters thus reducing overall system cost. The PM600 series maintain 0.3% line and 0.4% load regulation, and require no derating over the specified operating temperature range. Other specifications include: output voltage accuracy, 5.0%; ripple and noise, 20mV pk-pk; isolation, 300VDC. PM600 series DC/DC converters are intended for a wide variety of industrial applications, especially where tight regulation is required.
SPECIFICATION
OUTPUT SPECIFICATIONS Voltage accuracy Line regulation Load regulation Ripple and noise Transient response Temperature coefficient Short circuit protection
All specifications are typical at nominal input, full load at 25C unless otherwise stated GENERAL SPECIFICATIONS 5.0%, max. Efficiency Isolation voltage Switching frequency Case material Weight MTBF (75% FL) Single Outputs Dual Outputs Variable UL94V-0 50% typical 300VDC 40kHz to 70kHz Non-conductive black plastic 14g (0.5oz) 434,000 hours 268,000 hours
LL to HL NL to FL 20MHz BW See Note 5 Overshoot for 10% to 90% FL
0.3% 0.4% 20mV pk-pk, max. 0.1%, typical 0.01%C, typical
Output thermal limited
Continuous automatic recovery
ENVIRONMENTAL SPECIFICATIONS Thermal performance Operating ambient -25C to +71C Non-operating amb., -40C to +125C Case +95C, max. Derating None required Cooling Free air convection cooled Non-condensing Operating Non operating 5Hz to 500Hz 20% to 95% RH 10,000 feet max. 40,000 feet max. 2.5G rms (approx.)
INPUT SPECIFICATIONS Input voltage range Input filter Fault current mode 5VDC, See Note 10 4.5 to 5.5VDC 12VDC, See Note 10 10.8 to 13.2VDC See Note 8 Pi network 150% of FL input current Relative humidity Altitude Vibration
PAGE 1
SPECIAL APPLICATION MODELS
|
0.5-1W DC/DC
0.5 to 1 Watt Nominal input DC/DC converters
INPUT VOLTAGE 5VDC 5VDC 5VDC 5VDC 5VDC 12VDC 12VDC 12VDC OUTPUT VOLTAGE 5VDC 12VDC 15VDC 12VDC 15VDC 5VDC 12VDC 15VDC OUTPUT CURRENT 100mA 80mA 65mA 40mA 33mA 100mA 40mA 33mA INPUT CURRENT 260mA 380mA 380mA 380mA 380mA 100mA 145mA 145mA
(1)
TYPICAL EFFICIENCY 50% 50% 50% 50% 50% 50% 50% 50%
LINE
REGULATION (2) LOAD
(3)
MODEL NUMBER PM621 PM623 PM624 PM671 PM672 PM631 PM681 PM682
(6) (6) (4,6) (4,6)
0.3% 0.3% 0.3% 0.3% 0.3% 0.3% 0.3% 0.3%
0.4% 0.4% 0.4% 0.4% 0.4% 0.4% 0.4% 0.4%
Notes
Maximum figure, at full load. Measured from high line to low line. Measured as load changes from no load to 100% full load. The PM671 is available with optional voltage balance pin, and is designated by suffix letter `P'. For connection information, see case drawing. In addition, both the PM671 and PM672 are available with alternate pin-out (including balance pin) designated by suffix letter `R'. See case drawing. If not required, the balance pin can be left floating. 5 Measured with a 15F tantalum capacitor across each output. 6 On dual output models the four common pins are internally connected. The outputs can be returned through one pin while the others remain floating. 7 Standard specifications are conservative and can be optimized for specific applications. In particular, converter start-up at lower than specified temperature, wider input voltage range and output voltage adjustment are all relatively simple modifications to the standard product. Consult factory for details. 8 Fixed frequency design provides for easier input filtering and better noise performance. 9 Units are tested with resistive load only. 10 Output current derates to 0 at 110% nominal Vin. 11 NOTICE: Some models do not support all options. Please contact your local Artesyn representative or use the on-line model number search tool at http://www.artesyn.com/powergroup/products.htm to find a suitable alternative. 1 2 3 4
CASE F
0.08 (2.0) 0.02 DIA. (0.5)
24 23 22
1 2 3
1.25 (31.8) 0.10 (2.54)
15 14 13
(OPT.) 9
10 11 12
0.15 (3.8) 0.40 (10.2)
0.60 (15.2) 0.80 (20.3)
ALL DIMENSIONS IN INCHES (mm)
PIN CONNECTIONS PIN NUMBER 1 2 3 9 10 11 12 13 14 15 22 23 24 * PM671P.
ds_PM600_20050826.PDF
SINGLE OUTPUT MODELS +V Input Do not connect Do not connect No Pin -V Output +V Output -V Input -V Input +V Output -V Output Do not connect Do not connect +V Input
DUAL ALTERNATE PIN-OUT OUTPUT SUFFIX R (4) MODELS (6) +V Input -V Output Common Balance (opt)* Common +V Output -V Input -V Input +V Output Common Common -V Output +V Input +V Input +V Input +V Input No Pin Common Common Do not connect -V Output Balance +V Output -V Input -V Input -V Input
Balance Pin Connection:
24 23 22
1 2 3
Connect R1 as required to balance outputs when I + VoutI > I - VoutI
R1
(Opt.) 9
15 14 13
10 11 12
or R2
Connect R2 as required to balance outputs when I - VoutI > I + VoutI Input to balance pin: 5mA, max. R1 or R2: 3K Ohm, min.
Datsheet (c) Artesyn Technologies(R) 2005 The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein.
http://www.artesyn.com
PAGE 2

▲Up To Search▲

Price & Availability of PM600

	To Download PM600 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .